BS EN ISO 8780-1-1991 颜料和填充剂.色散特性评定用色散方法.第1部分:前言

作者:标准资料网时间:2024-05-28 07:53:05 浏览:8065 来源:标准资料网

【英文标准名称】:Pigmentsandextenders.Methodsofdispersionforassessmentofdispersioncharacteristics.Introduction
【原文标准名称】:颜料和填充剂.色散特性评定用色散方法.第1部分:前言
【标准号】:BSENISO8780-1-1991
【标准状态】:现行
【国别】:英国
【发布日期】:1991-04-30
【实施或试行日期】:1991-04-30
【发布单位】:英国标准学会(GB-BSI)
【起草单位】:BSI
【标准类型】:()
【标准水平】:()
【中文主题词】:涂料填充剂;分散(化工);颜料;填充剂;涂料
【英文主题词】:Bindingagents;Definitions;Dispersing;Dispersing(chemicaltechnology);Dispersions(chemical);Easeofdispersionbehaviours;Evaluations;Extenders;Incipients;Materialstesting;Methodsofdispersion;Opticaldispersivepower;Paintextenders;Paints;Pigments;Testing
【摘要】:Introductiontovariousmethodsfordispersingpigmentsand/orextendersinaparticularbindersysteminordertoassessthedispersioncharacteristics.
【中国标准分类号】:G54
【国际标准分类号】:87_060_10
【页数】:6P.;A4
【正文语种】:英语

下载地址: 点击此处下载

返回跳至顶部

上一篇: BS EN ISO 8780-4-1991 颜料和稀释剂.色散特性评定用色散方法.第4部分:研磨机评定色散
下一篇: BS EN ISO 8781-2-1991 颜料和稀释剂.色散特性评定方法.第2部分:研磨细度变化评定

【英文标准名称】:Informationprocessingsystems--Computergraphics--Programmer'sHierarchicalInteractiveGraphicsSystem(PHIGS)--Part1:Functionaldescription
【原文标准名称】:信息处理系统.计算机制图.程序员分层交互图形系统.第1部分:功能描述
【标准号】:JISX4221-1993
【标准状态】:作废
【国别】:日本
【发布日期】:1993-10-01
【实施或试行日期】:
【发布单位】:日本工业标准调查会(JISC)
【起草单位】:TechnicalCommitteeonInformationTechnology
【标准类型】:()
【标准水平】:()
【中文主题词】:计算机制图
【英文主题词】:computergraphics
【摘要】:
【中国标准分类号】:L81
【国际标准分类号】:35_140
【页数】:416P;A4
【正文语种】:日语

Product Code:SAE J400
Title:Test for Chip Resistance of Surface Coatings
Issuing Committee:Textile And Flexible Plastics Committee
Scope:This SAE Recommended Practice covers a laboratory procedure for testing and evaluating the resistance of surface coating to chipping by gravel impact. The test is designed to reproduce the effect of gravel or other media striking exposed paint or coated surfaces of an automobile and has been correlated with actual field results. The specific intent of the test is to evaluate organic surface coatings or systems on flat test panels; however, It may be possible to extend this type of testing to finished parts or other types of materials such as anodized aluminum or plated plastics if the results are interpreted with respect to the limitations and intent implied by the original testing procedures and rating system.This document may involve hazardous materials, operations, and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this document to consult and establish safety and health practices and determine the applicability of regulatory limitations prior to use.All dimensions are nominal unless otherwise noted.